News
-
Load Changes in Safety-Valve O-Rings During Repeated Lift Events
Executive Summary A safety valve that repeatedly lifts and reseats does not expose its sealing interface to one constant load state. Pressure forces, motion, contact compression, friction, recovery and impact effects can vary. Where an O-ring is present, its local contact condition may change. Th...Read more -
Holiday Notice: Yokey’s Mid-Autumn Festival Holiday Schedule 2026
As the Mid-Autumn Festival approaches, Ningbo Yokey Precision Technology Co., Ltd. would like to extend warm seasonal greetings to our customers and partners around the world. A Brief Introduction to the Mid-Autumn Festival The Mid-Autumn Festival is a traditional occasion that symbolizes reunion...Read more -
The Effect of Control-Valve Spool Oscillation on Seal Contact
Executive Summary In a modulating control valve, the moving trim element and its seal interface form one coupled mechanical boundary. Position changes, repeated reversals, lateral movement, tilt or unstable control and flow conditions can change seal contact over time. “Spool” is used here as a w...Read more -
Retention Zones and Cleaning Dead Spots in Hygienic Pump Seal Grooves
Executive Summary In a hygienic pump, the seal groove is both a sealing feature and a flow-access, venting and drainage boundary. Depth, side clearance, corners, surface condition and compression can create a product-retention zone that is difficult to wet, scrub and drain during CIP. The same ge...Read more -
Low-Flow Lubrication Instability in Metering-Pump Plunger Seals
Executive Summary A metering-pump plunger seal operates under reciprocating sliding, cyclic pressure and repeated start-stop conditions. Its behavior depends not only on seal material and preload, but also on whether lubricant or flush fluid can continuously replenish the local contact. When supp...Read more -
Impact Fatigue and Backflow at Diaphragm-Pump Ball-Valve Seals
Executive Summary A changed flow response, pressure trace or suspected backflow in a diaphragm pump is a condition-dependent engineering observation. Repeated ball-to-seat seating events may alter contact conditions through local loading, surface damage or a change in how the ball settles. Simila...Read more -
Thermal-Cycling Response of Static Seals in Magnetic-Drive Pump Containment Shells
Executive Summary A changed sealing response after thermal cycling is a condition-dependent observation, not automatic proof of static-seal failure. Heating and cooling may change relative dimensions, contact pressure, compression retention, stress relaxation, fluid exposure, particle position, p...Read more -
Outgassing Changes in Clean-Equipment Seals After Low-Temperature Transport
Executive Summary A change in clean-equipment seal outgassing after low-temperature transport should initially be treated as a state- and measurement-dependent observation, not automatic proof of permanent seal damage. Cooling and storage may alter molecular mobility, moisture distribution, adsor...Read more -
Crystal Deposition and Restart Leakage at Wet-Process Equipment Drain Seals
Executive Summary Restart leakage at a wet-process equipment drain seal should be treated as a sequence-dependent boundary symptom, not automatic proof of seal-material failure. Liquid residue may remain near a drain outlet, dry into a deposit, alter local contact or restrict the discharge path, ...Read more -
Alternating Media Exposure of Semiconductor Gas-Line Purge Valve Seals
Executive Summary Alternating media exposure in a semiconductor gas-line purge valve should be treated as a sequence-dependent valve-boundary condition, not automatic proof of seal-material incompatibility or valve failure. A seal may encounter different chemical, pressure, temperature and purge ...Read more -
Thermal-Gradient Deviation at Wafer Chuck Cooling-Channel Seals
Executive Summary Thermal-gradient deviation around a wafer chuck cooling-channel seal should be treated as a coupled system condition, not automatic proof of seal-material failure. A nonuniform thermal map may be associated with differential expansion, contact-pressure redistribution, cooling-ch...Read more -
Condensate Buildup at Vacuum Pump Exhaust-Side Seals
Executive Summary Condensate buildup near a vacuum-pump exhaust-side seal should be treated as a system-boundary symptom, not automatic proof of seal-material failure. Condensation depends on vapor composition, temperature profile, pressure history, flow path, surface condition and drainage. The ...Read more